10年專注重型紙箱定制生產廠家

精密儀器,電子電器,瓦楞紙箱等包裝解決方案提供商

1. In the process of using the pallet, the distance between the fork teeth should be as wide as possible to the outer edge of the fork inlet of the pallet, and the fork inlet depth should be more than 2 / 3 of the whole pallet depth.

2、叉車在運用吹塑托盤運動過程中，應保持勻速度進退和上下，防止急剎、急轉引起托盤受損、形成貨品坍毀，此款托盤不適合上貨架運用。

2. Forklift in the use of blow molding tray movement process, should maintain a uniform speed forward and backward and up and down, to prevent sudden brake, sudden turn caused by pallet damage, the formation of goods collapse, this type of pallet is not suitable for shelf use.

3、應輕放塑料托盤，防止落地時受力不均，發作損壞。

3. The plastic tray should be put gently to prevent uneven stress and damage when landing.

4、放置貨品時，應均勻放置，防止起升搬運時，發作側歪。

4. When placing goods, should be evenly placed, to prevent lifting and handling, the occurrence of skew.

5、運用搬運設備時，應考慮貨差尺度是否適合此塑料托盤運用，防止尺度不合適，撐壞塑料托盤。

5. When using the handling equipment, we should consider whether the cargo size is suitable for the use of the plastic pallet, so as to prevent the improper size from damaging the plastic pallet.

6、堆垛運用時，應考慮下面一塊托盤的承重。

6. When stacking, the load bearing of the pallet below should be considered.

標準托盤

Standard tray

正確的運用塑料托盤應該做到包裝組合碼放在塑料托盤上加上恰當?shù)睦υ凸阌诶脵C(jī)械裝卸和運送，然后滿足裝卸、運送和存儲的要求。

The correct use of plastic pallets should make sure that the packaging combination is stacked on the plastic pallets with proper binding and wrapping, so as to facilitate mechanical loading and unloading and transportation, and then meet the requirements of loading, unloading, transportation and storage.

標準托盤可以長久地運用，希望按下列要求正確運用塑料托盤：

Standard pallets can be used safely for a long time. We hope to use plastic pallets correctly according to the following requirements:

1、塑料托盤應防止遭受陽光暴曬，避免引起老化，縮短運用壽命。

1. The plastic tray should be protected from the sun to avoid aging and shorten the service life.

2、禁止將貨品從高處拋擲在塑料托盤內。合理確定貨品在托盤內的堆積方式。貨品均勻置放，不要集中堆積，偏疼堆積。承載重物的托盤應放在平整的地面或物體表面上。

2. It is forbidden to throw goods in plastic pallets from high places. Reasonably determine the stacking mode of goods in the pallet. Goods evenly placed, do not focus on the accumulation, the accumulation of pain. The tray carrying heavy objects should be placed on a flat ground or object surface.

3、禁止將塑料托盤從高處拋落，防止因猛烈地碰擊而形成托盤破碎、裂紋。

3. It is forbidden to throw the plastic pallet from high place to prevent the pallet from breaking and cracking due to violent impact.

4.叉車或手動液壓車作業時，叉刺盡量向托盤叉孔外側靠足，叉刺應悉數伸進托盤內，平穩抬起托盤后才可變換角度。叉刺不行碰擊托盤側面避免形成托盤破碎、裂紋。。

4. When forklift or manual hydraulic truck is working, the forks should be close to the outside of the fork hole of the pallet as far as possible. All the forks should be extended into the pallet, and the angle can be changed only after the pallet is lifted smoothly. Forks shall not strike the side of the pallet to avoid the formation of pallet breakage and cracks..